Contents
Operating a forklift requires constant awareness, proper training, and strict adherence to safety best practices. Every year, thousands of preventable workplace injuries occur due to improper forklift operation, often putting both operators and nearby pedestrians at risk. By following proven safety guidelines and enforcing consistent training and workplace policies, companies can significantly reduce hazards and create a safer, more efficient environment for everyone.
1) Use Safe Speeds
Forklifts are not designed to move about at high speeds. The maximum speed for most forklifts doesn’t exceed 10 miles per hour. However, standard forklifts weigh between 8,000 and 9,000 pounds, and the biggest can weigh over 100,000 pounds.
When such heavy machines move at 8 or 9 miles per hour, they can be more dangerous than smaller vehicles moving at higher speeds on the road. This because:
- It takes a lot of effort to stop the forklift, leading to a greater braking distance.
- Like all vehicles, the forklift is less stable at high speeds and can easily tip over.
- It’s easy to lose control of the forklift at high speed and cause a collision.
- Bringing the forklift to an abrupt stop from high speed can upset or spill the load.
These risks are even more significant when the forklift is carrying a very heavy load, moving through tight spaces, wet areas, or heavily trafficked areas, or when the driver’s vision is obstructed.
Guidelines on Safe Speed
OSHA doesn’t provide a specific speed that is considered safe for forklifts. The Material Handling Equipment Distributors Association, or MHEDA, recommends 3mph in areas with heavy pedestrian traffic and never more than 8mph.
Determining safe speeds is left to employers, and this makes sense because different workplaces have different conditions. OSHA does state that forklifts should be operated at speeds that allow them to be safely stopped and slow down on wet floors.
To determine a safe speed for your company’s forklifts, you’ll need to consider factors such as the type of terrain (even or uneven), floor surface (rough or smooth), presence of inclines, operator visibility in different sections, type of forklift, presence of pedestrians, etc.
Enforcing Safe Forklift Speed Limits
It’s not enough to set a speed limit for forklifts. These speed limits should be enforced. You can reduce the risk of forklifts moving at unsafe speeds by:
- Offering good quality training to forklift operators. According to OSHA, this alone can reduce accident risk by 70%.
- Ensure corrective action is taken when operators are caught speeding e.g. requiring refresher training.
- Put up signs that indicate speed limits in different areas.
- Install speed limiters in the forklifts.
- Put up a radar system to detect speeding forklifts
- Install speed bumps where necessary
2) Avoid Abrupt Stops
Abruptly stopping a forklift can cause it to slide, tip over, or spill the load. When a forklift tips over, it is a danger to the operator and anyone nearby. Spilling a load can cause injuries, damage the cargo and other equipment, or damage infrastructure.
Effect of Sudden Stops on Forklift Balance
Forklifts weigh thousands of pounds. When the brakes are suddenly applied, the wheels may stop turning, but the forklift’s momentum will shift its center of gravity forward, outside the stability triangle, making the forklift unstable.
This is especially risky when the forklift is loaded because its center of gravity is closer to the front. Abrupt stops are a bigger problem at high speeds since momentum increases with speed.
How to Avoid Abrupt Stops
Measures you can take to prevent sudden stops by forklift operators include:
- Forklift operator training: Forklift operators should be trained to bring the machines to a smooth stop. They should also be trained to accurately judge braking distances at different speeds, loading conditions, floor conditions, etc.
- Enforce speed limits: When forklifts are moving at reasonable speeds, operators are less likely to have to stop abruptly since they’ll have better situational awareness. The effect of an abrupt stop is also less significant at lower speeds.
- Separate pedestrian and forklift traffic: Operators are likely to stop abruptly because of pedestrians. Separating pedestrian and forklift traffic limits encounters between the two.
- Maintenance: Forklifts that brake erratically can lead to abrupt stops. Ensure the braking system in the forklift is well-maintained so operators can use it reliably.
- Situational awareness: Drivers should be cautious and aware of their surroundings at all times. The company or warehouse should also put up signs that warn forklift operators of risks ahead or in their immediate vicinity.
3) Pedestrians Always Have the Right of Way
36 percent of people who die in forklift-related accidents are pedestrians according to OSHA. Many of these pedestrians are struck when forklifts tip over, while others are caught between the machine and a surface or between two forklifts. A small number have also been run over.
These statistics paint a grim yet important picture. Pedestrians will always come off worse in an interaction with a forklift.
The Rules In Forklift-Pedestrian Interactions
OSHA states that pedestrians have the right of way over forklifts. This means that if a forklift operator comes across a pedestrian, they should stop and wait until the pedestrian passes before continuing on their designated path.
Forklift operators should also move cautiously in areas with heavy pedestrian traffic. This means moving at a controlled speed while remaining aware of their surroundings.
Additional Forklift Safety Tips To Protect Pedestrians
In addition to moving at a controlled speed and yielding to pedestrians, forklift operators can also take the following measures to avoid accidents with pedestrians:
- Walk the route before driving through to make note of hazards and potential points of interaction with pedestrians.
- Use a spotter when the situation requires it
- Use the horns when coming up to blind corners
- Use both an audible alarm and a visible flashing light when backing up
- Not allowing anyone to pass or stand under the forks or load
- Warning pedestrians when there isn’t enough space
The company can also take measures to protect pedestrians, including:
- Ensuring drivers are well trained on how to safely operate forklifts near pedestrians.
- Separating pedestrian and forklift traffic by creating designated walkways around the company. OSHA also requires that these passageways be well-marked and unobstructed.
- Inspecting and maintaining forklifts to prevent accidents caused by mechanical failure.
- Putting up signs to control traffic
- Installing mirrors at blind intersections
4) Don’t Pick Up Other Riders
Almost all forklifts are designed to have a single person onboard, i.e., the operator. Having an extra person on board puts the operator, the rider, and anyone nearby at risk.
Risks of Riding On Forklifts
Riding as an extra person on a forklift can be dangerous regardless of where or how you choose to sit. Here’s why:
- Sitting on a fork or on top of objects carried by the fork is not advisable because it will be difficult to keep your balance. Sitting on a load may offer better balance, but this can make the whole forklift unbalanced, causing it to tip over. Additionally, should the rider fall or get off while the forklift is in motion, they could easily be run over.
- Sitting at the back of the forklift doesn’t work either because there is no way to maintain balance. This also shifts the forklift’s center of gravity and can cause it to tip. Falling from the back of the forklift can lead to injury or worse especially if the forklift is reversing.
- Sharing the operator’s seat puts the rider, operator, and everyone around them at risk. The rider may accidentally hit a control mechanism, causing the operator to lose control of the forklift.
- In case of a forklift malfunction or accident, even one caused by something else, the rider will be in greater danger because they have no seatbelt to keep them from jumping or getting thrown in the path of a tipping or rolling forklift.
Preventing Extra Riders On Forklifts
Drivers should be informed of the dangers of picking up riders on their forklifts. The company should also have a strict policy against having riders on forklifts.
Forklifts are occasionally used to help workers access elevated areas. In such situations, an access cage must be used. Avoid lifting workers on makeshift platforms such as pallets.
The access cage and its contents should not exceed half the forklift’s carrying capacity. People should also not be moved about in the access cage, especially when elevated.
5) Be Aware of Fork Position
Forklift operators should be aware of the position of the forks, whether the forklift is loaded, unloaded, parked, in motion, or lifting an item. Knowing the position of the fork will help them assess the risk level accurately in different scenarios.
When the forks are in the wrong position, they can make the vehicle less stable, especially when carrying a load. Incorrectly positioned forks also create a tripping hazard when the vehicle is parked and cause more severe injuries in an accident involving the forklift.
Fork Position When Parked
When a forklift is parked, the forks should be positioned to make them less of a tripping hazard. The forks should be as low as possible with the tips flat on the ground. This is achieved by tilting them downwards before lowering them completely.
The forks should not be lowered to the ground before being tilted because this stresses the lifting mechanisms when the forks are lifted by the next driver.
Fork Position When Moving
When the forklift is in motion, the forks should be no less than 2 inches off the ground on flat surfaces. Some forklift manufacturers recommend at least 4 inches. This ensures the forks clear any uneven areas, inclines, slopes, or debris on the ground.
When using the forklift outdoors, the forks should be slightly higher to ensure they clear rocks or anything else on the ground.
The forks should not be more than 10 inches off the ground when the vehicle is moving. Some experts recommend a maximum of 8 inches. If the fork is carrying a load, the forks and the load should be tilted backward. This helps to keep the forklift stable.
The fork position should never be adjusted when the vehicle is in motion.
The Role of Operator Training
The best way to ensure operators position forks properly is with proper training. Operators will need to adjust the position of the fork many times in a shift including when:
- Parking the forklift
- Picking up a load
- Unloading to an elevated position
- Moving around without a load, etc.
They will need a lot of training and reinforcement to remember how to position the forks correctly in each situation.
6) Keep The Load Level and Stationary when in Motion
There is a high risk of a tip-over when a forklift is moving and carrying a heavy load. This risk is even higher if the load is not properly balanced or secured. An unbalanced or unsecured load is likely to move when the forklift is in motion, abruptly shifting the center of gravity. Such loads can also fall off the forklift and be damaged or cause an injury.
Handling Standard Loads
To lower the risk of a load shifting when the forklift is moving, the load should be placed such that its weight is evenly distributed. Loose loads should be tied or stacked to minimize movement during transportation. The load should never exceed the forklift’s capacity.
The forks should be spread as wide as possible for better load distribution. They should also be fully under the load. When the forks are not fully under the load, the center of gravity will be farther forward than it needs to be, increasing instability.
The forks should be at least two-thirds of the way underneath the load. They should be tilted slightly back to improve stability when the forklift is in motion. The forks should never be tilted forward when the forklift is moving. Operators should exercise caution when moving over uneven, sloped, or rough surfaces, as these can cause the load to shift.
Handling Uneven Loads
Extra caution should be exercised when transporting uneven loads because they are more likely to shift when the forklift is in motion. Some guidelines for keeping such loads level and stationary are:
- Keep the heaviest part of the load as close as possible to the front wheels
- The load must be secured using a rope, banding, or shrink-wrap
- Ensure the load is well below the forklift’s load capacity
- Move at low speeds only. The faster the load is moving, the more likely it is to become more unstable.
- Damaged items that could break or fall apart when being moved should not be transported until they are secured.
- Don’t lift loads with only one fork
The operator should always assess each load and make an informed decision about how best to carry it.
7) Slow Down & Sound Horn at Corners
Cornering is a maneuver that must be handled carefully on a forklift. Cornering at high speeds is a common reason why forklifts tip over. When a driver can’t see what’s around a corner, there is also a higher risk of a collision.
Cornering Increases Instability
When any vehicle is going around a corner, it is subjected to additional forces that make it unstable. The magnitudes of these forces increase with speed, which means the faster the forklift is going around a corner, the more likely it is to tip over.
Any load carried by the forklift will also be affected by these forces. This can cause them to shift and make the forklift unstable. The risk of a load shifting during cornering is even higher if the load is being carried high, when the load is close to the upper limit of the forklift’s capacity, or when the load is not centered.
Poor Visibility Around Corners
Visibility around corners can also be poor. This increases the risk of the forklift colliding with a pedestrian, an obstruction in its path, or another forklift. This can be worse if the forklift is carrying a load that partially obstructs the operator’s view.
Preventing Accidents While Cornering
The risk of tipping over or a collision while cornering can be reduced by:
- Slowing down: Moving slowly while cornering reduces the forces acting on the forklift and the load. It also gives the operator time to spot and react to dangerous situations.
- Use the horn and visible alerts: Sounding the horn will alert any pedestrian or operator that a truck is coming. Visible alerts such as flashing lights can also alert people who may not hear the horn, e.g., in a busy warehouse or loud manufacturing plant.
- Signage: The company should put up signs that warn pedestrians and forklift operators when they are approaching a blind corner. Activated signage and proximity alert systems can also be used to counter sign blindness.
- Install and use mirrors: Mirrors should be installed on both the forklift and around the warehouse at blind spots. All workers should be trained on how to use warehouse mirrors to spot hazards around corners.
- Remain alert: Forklift operators should remain alert and never be lulled into a false sense of security. Poor situational awareness is still a common cause of accidents. Pedestrians should also be advised on the dangers of moving and working in a shared area with forklifts.
8) Keep Right / In Lane
In the US and Canada, vehicles are driven on the right side of the road. Forklift operators and pedestrians in these regions will be inclined to drive and walk on the right side. It’s, therefore, a good idea to keep to the right to minimize the risk of collision.
Stay In Lane
Many companies and warehouses will also have lanes marked out for forklift traffic. Operators should ensure they stay in lane to minimize the risk of collisions with pedestrians outside the lanes or oncoming forklifts in the left lane.
How to Separate Forklift Traffic
Keeping forklift traffic separate is a good way of avoiding collisions. Some measures you can use to achieve this are:
- Keeping right should be the rule for forklift operators, not just a suggestion
- Marking out lanes to be used by forklifts
- Installing lane departure systems on forklifts to alert operators when they are leaving their designated path
- Installing guards and rails to serve as a physical barrier between forklifts and pedestrians, especially in areas with heavy forklift traffic
- Pedestrians should be well-trained or advised on the need to keep right when walking in areas with forklift traffic
9) Watch Out for Blind Spots
Blind spots are some of the most common reasons behind forklift-related accidents. Many workers have experienced the shock of stepping out onto an aisle or turning a corner only to find a forklift coming towards them at an uncomfortable speed.
Many workers are only alive today because the forklift operator managed to stop the truck in time, but others haven’t been as lucky.
Where Do You Find Blindspots
A blind spot is any location where an operator’s visibility is limited. A common blind spot is any sharp corner along the path of the forklift. The driver can’t see what’s around the sharp corner, and this can lead to an accident. However, blind spots can be created in other places, including:
- Where a door opens up to an aisle
- In the outdoors when the weather is poor
- Plant or warehouse sections where a lightbulb is out
- Near large or stacked loads
An operator’s view can also be obstructed by a large load. The fork carriage, mast, and other forklift parts can also obstruct the driver’s vision without a load. If the driver’s view is significantly obstructed by a load, they should travel in reverse.
Avoiding Collisions In Blindspots
It’s not possible to eliminate blind spots, but with certain precautions, driving near them can be safer. Precautions that can be put in place include:
- Slowing down: Moving at a slow speed makes it easier to notice blind spots and stop the forklift in case another forklift or a worker is coming from the other side. A slow speed also reduces the shock of an abrupt stop, which might destabilize a heavy load.
- Use a spotter: Having someone looking around the corner and warning others of your approach is a simple way of avoiding collisions.
- Install pedestrian safety lights: These lights are aimed some distance around the forklift and alert pedestrians of your approach. They can also form a virtual boundary around the forklift to keep pedestrians back.
- Use mirrors and cameras: Use the forklift’s mirrors and cameras to know what is happening around you. Convex mirrors can also be installed near blind spots so operators and pedestrians can see what’s around the corner.
- Pay attention to lighting: Whether it’s bad weather outdoors or a darker area in the warehouse, the forklift driver should take note of any changes in lighting conditions.
10) Keep Alert to Floor Conditions
Floor conditions in most workplaces are not constant. Indoor floors can become slippery due to spills or uneven due to wear. There’s also the danger of protruding boards and nails on wooden flooring. Floors also have loading limits, and these can be exceeded by the forklift’s weight.
Floor conditions can be even less predictable outdoors. Weather conditions can render the ground wet, muddy, unstable, or icy. None of these conditions is ideal for driving a forklift over.
Some parts of the floor or ground may also be smooth or rough by design. Both conditions present different challenges for forklifts.
How Floor/Ground Conditions Compromise Forklift Safety
Driving a forklift over different types of floors or in certain conditions can create challenges such as:
- Increased braking distance: When the ground or floor becomes slippery due to spills or wet weather, it can be harder to bring the forklift to a stop. Without extra precaution, the operator can easily slide and cause a collision.
- Sudden shifts in load balance: This can happen if unstable ground or flooring under one or more wheels gives way. It can also happen if the vehicle slides uncontrollably on a wet surface.
- Bouncing of the load: Ground conditions that shake the forklift will also shake the load. On rough roads, this can cause loads to bounce up and down and move out of position, making the forklift unstable and more likely to tip over.
- Collision: When there are sufficiently high protrusions or debris on the floor or ground, they can be hit by one of the forks. Depending on the speed and loading conditions, this can cause the forklift to tip over.
Avoiding Floor Related Forklift Accidents
Forklift operators and the company can avoid floor-related accidents by following measures such as:
- Inspecting the floor before using the forklift and not using the forklift on very slippery or unstable ground
- Driving slowly when the floor is very rough/bumpy or when moving over slippery areas.
- Taking note of floor loading limits and not exceeding them
- Choosing an appropriate load height to avoid hitting protrusions
- Removing debris from the forklift’s path or choosing an alternative path
- Repairing floors and reinforcing outdoor areas that are driven over by forklifts
Conclusion
Forklift safety isn’t just about compliance—it’s about protecting lives. By maintaining responsible speeds, preventing abrupt movements, respecting pedestrians, and keeping loads secure, operators can dramatically reduce the likelihood of accidents. Combined with strong company policies, clear signage, and ongoing training, these rules ensure forklift operations remain safe, controlled, and effective throughout the workplace.
Additional Resources
- 15 Forklift Safety Tips [Industry Expert Advice for Safe Operation]– creativesafetysupply.com
- Forklift Safety in 6 Steps– safetyblognews.com
- 10 Rules For Forklift Safety– creativesafetypublishing.com
- 3 Safety Signs for Warehouse Traffic Control– blog.creativesafetysupply.com
- Warehouse Traffic Control to Improve Forklift Safety– floor-tape.com
- The Importance of Forklift Operator Training– babelplex.com
- Forklift Operator Safety Tips– hiplogic.com
- Floor Marking for Warehouse Traffic– floormarkingpro.com
- Warehouse Floor Marking Tapes for Safety– aislemarking.com
